ADC0808CCN DATASHEET PDF

The ADC ADC data acquisition component is a monolithic CMOS device with an 8-bit analog-to-digital con- verter 8-channel multiplexer and. ADCCCN Texas Instruments Analog to Digital Converters – ADC Obsolete, LTB expires Nov 6, datasheet, inventory, & pricing. ADCCCN datasheet, ADCCCN circuit, ADCCCN data sheet: NSC – 8-Bit uP Compatible A/D Converters with 8-Channel Multiplexer.

Author: Zunris Fenrile
Country: Samoa
Language: English (Spanish)
Genre: Business
Published (Last): 26 March 2016
Pages: 224
PDF File Size: 14.97 Mb
ePub File Size: 2.60 Mb
ISBN: 722-3-16391-880-9
Downloads: 62362
Price: Free* [*Free Regsitration Required]
Uploader: Gagor

SPI Module of Arduino. Has to be made high to get output on output pins. Vref is connected to ground normally. The obtained value is 2. Or even to use as a standalone ADC module. The default step size is These three bits have to be set as shown in the ddatasheet below to access the respective analog datashret. As you can see in the image the voltage value is 2.

The input which is to be converted to digital form can be selected by using three address lines.

IC ADC0808

Clock input; to provide external clock. Submitted by admin on 13 October Since the ADC IC can measure up to eight Analog voltage and also does not have an internal clock slightly requires more components to make it work compared to its predecessor ADC The step size is decided based on set reference value.

  KNOWING CALEB HAWKINS RANCH 4 CAMERON DANE PDF

Interface GPS with Arduino. TL — Programmable Reference Voltage.

Powers the IC typically with 5V. Connect to ground of the circuit. Digital output bit 4. Step size is the change in analog input to cause a unit change in the output of ADC. Output 2 -1 to 2 End of Conversion EOC. Output digital pins which gives the result of the ADC conversion. ADC is an 8 bit analog to digital converter with eight input analog channels, i.

Start conversion; input pin; a low to high pulse is given. End of conversion; output pin; goes low when the conversion is over. This high-density System-in-Package SiP integrates avc0808ccn, power switches, and support adx0808ccn. This pin is should be temporarily made high to select ADC channel. Has to be given clock signals 0V-5V 20Mhz approx. The right input analog voltage can be given to pins from IN1 to IN7, but the IC can read the voltage of only one channel at a time.

When the conversion is complete the EOC pins goes low to indicate the end of conversion and data ready to be picked up.

What is Web Browser. Analog Channel 1 to 5. Input pin; a low to high pulse brings data to output pins from the internal registers at end of conversion.

  KEMAHIRAN MENERANG PDF

Arduino based GPS receiver. These three pins are used to select the channel. Skip to main content. The ADC needs some specific control signals for its operations like start datashwet and bring data to output pins.

Choosing Motor For Robots. This is an input pin which is made high to start conversion. This is an output pin which goes high once the conversion is over. These 7 pins are the input pins for Analog voltage sensor. Choosing Battery for Robots.

ADC IC Datasheet | ADC Pin Configuration

In the above circuit I have used a potentiometer to feed in a variable voltage of 0V to 5V to the IN1 pin and the present Voltage is read using a voltmeter. Hence, if you are looking for a ADC module with a decent resolution of 8-bit that could adc0808cdn up to 8 channels then this IC is for you.

Virgin Galactic — Commercial Space Flight. Once the channel is set it should be enabled by making the Address latch enabled ALE pin to go high momentarily.

Interface SD Card with Arduino. That is for every increase of It is a pin Eight channel 8-bit ADC module.