ARITECH CD72 PDF

Thank you for choosing an ARITECH security system. This manual explains how to use the ARITECH CD72 and CD95 series for every day use. There is a. A dual com polls to the monitoring station. What this means is every couple of minutes (depending on what it is set up for) it sends a signal to the monitoring. Hello, I want to integrate a solution based on PLUGWISE and an Aritech Alarm Central. I could successful connect a printer SERIAL RS

Author: Fenririsar Nezuru
Country: France
Language: English (Spanish)
Genre: Photos
Published (Last): 23 April 2010
Pages: 51
PDF File Size: 20.63 Mb
ePub File Size: 11.94 Mb
ISBN: 333-8-57731-472-9
Downloads: 62878
Price: Free* [*Free Regsitration Required]
Uploader: Manos

Remote 1 must be a keypad. The alarm and tamper are placed together in one zone. Find More Posts by mick Only keypad 1 is operational. U kunt hieronder aangeven waarom deze vraag ongepast is.

Handleiding Aritech TD TD (pagina 6 van 32) (English)

Set the DIP switches of all the remote keypads and expanders. Wij controleren de vraag en zonodig cc72 deze verwijderd. Dual loop Connecting a detector with latch Note: If dual loop is programmed, the letter T will appear next to the zone number to indicate the tamper section of the loop is open. In the CD the expanders have priority over the keypads! CD, remotes 2 to 4 must be keypads and remotes 5 and 6 expanders. Keys on a CD30xx Note: If dual loop is programmed, the letter T will appear next to the zone number to indicate the tamper section of the loop is open.

If any zones shown are 24Hr zones e. If the tampers must be placed in separate zones, they can be connected according to figure 1 1 end-loop resistor or figure 2 2 end-loop resistors see page 8.

  COPLAND THE CAT AND THE MOUSE SCHERZO HUMORISTIQUE PDF

Enter text from picture: Overview of the inputs and outputs on the CD Output no. Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Thanks for the response lads putting this project on hold until I dc72 a few quid together to buy hardware for the job. Everybody involved in installing or maintaining this panel should have access to a copy of this manual. When the connection with the short circuit is removed the power supply will return to 12 volts.

Use of an extra power supply This is particularly important when such ducts contain cables supplying electric motors, fluorescent lights or 3-phase power. The resistance calculation is as follows: Connecting a fire detector Maintain a good separation between low voltage and mains supply cables, and use separate points of entry into the control panel cabinet. Detectors or key switches can be connected in two ways: The software version is displayed on the other keypads if present.

The zone is Resistance Panel zone arjtech Remote zone voltages Reaction on standby 3k5 – 6k2 cd722. Originally Posted aritrch masterbates1 thanks, you say polls aritechh this like a test call? No part of this publication may be reproduced, transmitted, stored in a retrieval system, or transmitted in any form, or by any means – electronic, photocopying, recording, or otherwise – without the prior written permission of SLC BV.

Aritech ADVISOR CD72 Manuals

Connection of a fire detector Note 1: The use of cable ties is recommended and improves neatness in the box.

  LM393P DATASHEET PDF

The arrows move the cursor during entry.

Email deze handleiding Delen: By continuing to browse this site you are agreeing to our use of cookies. Please sign up or log in to join the discussion. Auxiliary power supply PG 4-wire bus of keypad or expander Figure Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email.

Any programming changes made may not take effect until you exit programming mode. If this is not done, the system will be triggered as soon as it is switched on.

CD30xx stands for the keypads: Supply only mains power to the control panel. Separate alarm and tamper connection The zone has two end-loop resistors 4. If the sirens have been activated, these will now stop.

Aritech TD8803 TD8412

Both zones should be closed with an end-loop resistor 4. The switching of these relays may cause electrical interference. Connecting a relay or an LED on the output Wij vragen u dus ook te reageren op een antwoord.

Location Output connected max. One zone each is required for both tamper and the alarm.

Overview of the dipswitches on remotes The greatest care should therefore be taken when installing this cable. Don’t show me this message again.