ASTM A493 PDF

Above values from ASTM A Higher strengths can be produced by heavy cold work – this may be required for certain applications. ASTM A – 16 Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging. This specification covers. See the chemical composition and physical properties of ASTM A Grade annealed Stainless Steel, find alternative materials, and connect with suppliers.

Author: Mazukora Shajind
Country: Monaco
Language: English (Spanish)
Genre: Art
Published (Last): 1 May 2015
Pages: 259
PDF File Size: 13.30 Mb
ePub File Size: 5.44 Mb
ISBN: 650-2-12954-889-4
Downloads: 61001
Price: Free* [*Free Regsitration Required]
Uploader: Voodoolrajas

ASTM A493 for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging

The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. A superscript epsilon e indicates an editorial change since the last revision or reapproval. Originally published as A — Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

General Requirements for Delivery 4.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. This standard has been approved for use by agencies of the Department of Defense. Soap is generally used.

Packaging and Package Marking 9. Resistance to Intergranular Corrosion 8. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

  CATALOGO ENELPREMIA 2013 PDF

The following coatings may be specied: The following lubricants may asrm specied: An electroplated copper coating is often used.

ASTM A493 Grade 384 annealed

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ve years and if not revised, either reapproved or withdrawn.

Historical Version s – view previous versions of standard.

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own astj.

The SI equivalents are in parentheses and may be approximate. NOTE 1—A typical ordering description is as follows: B Product analysis tolerance over the maximum limit for carbon and nitrogen to be 0. The material shall also conform to the requirements as to asm properties.

Copyright ASTM Standard Specication for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging1 This standard is issued under the xed designation A ; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. The steel shall conform to the required chemical composition requirements. Material can be manufactured to tensile strength ranges other than those shown in Table 2.

The producer should be consulted when material is required to tensile strength ranges other than those specied. Such requirements may include, but are not limited to the following: Link to Active This link will always route to the current Active version of the standard. Current edition approved Jan. The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

  FINANCIAL AND MANAGEMENT ACCOUNTING AN INTRODUCTION PAULINE WEETMAN PDF

ICS Number Code Last previous edition A — Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters.

ASTM A for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging

For smaller sizes, similar mechanical properties apply to ferritic and martensitic grades; however the producer should be consulted regarding somewhat higher tensile properties applicable to austenitic grades. All austenitic grades in the annealed condition or annealed and lightly drafted condition shall be capable of passing the criteria set by this specification.

It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. A number in parentheses indicates the year of ast reapproval. This specification covers cold-finished and hot-finished stainless steel wire and wire rods for cold heading or cold forging for applications, such as fasteners, where corrosion resistance is a factor. This abstract is a brief summary of the referenced standard.