CCNP SWITCH 6.0 INSTRUCTOR LAB MANUAL PDF

CCNP SWITCH 6 – BitRadius. Instructor Lab Manual Book everyone. Download file Free Book PDF Ccnp Switch Instructor Lab Manual at. CCNP: Implementing Secure Converged Wide-area Networks v – Lab Copyright © Ensure that the switch is set up so that both the router and host are in the same. VLAN. .. Figure Internet Explorer Security Alert Prompt. ccnp switch instructor lab pdf. CCNP SWITCH Instructor Lab Manual. This document is exclusive property of Cisco Systems, Inc.

Author: Shall Tegrel
Country: Egypt
Language: English (Spanish)
Genre: Technology
Published (Last): 19 December 2011
Pages: 38
PDF File Size: 17.74 Mb
ePub File Size: 6.85 Mb
ISBN: 302-2-82335-175-6
Downloads: 76907
Price: Free* [*Free Regsitration Required]
Uploader: Mele

It is not necessary to specify the maximum number of addresses, unless it is greater than 1.

Once authenticated, the user is allowed access to the manua resources. Verify your configuration to make sure that root guard was not accidentally configured on a port that should hear root advertisements, such as a port on ALS2 that is connected to the root bridge.

CCNP SWITCH Lab Manual, 2nd Edition

To maintain an efficient STP topology, the root bridge must remain predictable. Skip to main content. Verify the EtherChannel configuration using the show etherchannel command. Prepare the switches and routers for the lab. The following commands configure the switch port mode as access, place the port in the proper VLANs, and turn on spanning-tree PortFast for the ports.

When you restart the WLAN controller, a configuration wizard prompts you to enter basic configuration instrucyor.

  EL DIABLO MUNDO JOSE DE ESPRONCEDA PDF

ccnp-switch-instructor-lab-manual-slm

VTP server is the default mode. This is the result of the channel-group x mode being set to active.

In addition, configure a loopback interface on the ISP router to simulate an external network. Notice that all ports are forwarding because it is the root switch. If that is the case, read through those portions of the lab that deal with their configuration to become familiar with the process and commands. No labs for this chapter. By default, issuing the switchport port-security command by itself sets the maximum number of MAC addresses to 1, and the violation mode to mwnual. DLS1 show etherchannel summary Flags: The output should look similar to the following.

Background Inter-VLAN routing using an external router can be a cost-effective solution when it is necessary to segment a network into multiple broadcast domains. Absolute SecureStatic Address Aging: This determines how far away the root bridge is. The instance number can be between 0 and Use cisco as both the username and password. Issue the show interfaces trunk command on DLS2. It is good practice to shut down the ccp on both sides of the link before a port channel is created and then reenable them after the port channel is configured.

Lab Implement Spanning Tree Protocols. Background VLANs logically segment a network by function, team, or application, regardless of the physical location of the users.

The new cost values are: Enable broadcast storm control on trunk ports. It is possible that a switch could be accidentally or maliciously added to those ports.

  ASTM A255 10 PDF

Configure the host ports for the appropriate VLANs according to the diagram. This document is exclusive property of Cisco Systems, Inc. This document is Cisco Public Information. The following is a sample instrcutor for the Why do you think this is the case?

Cisco Networking Academy, CCNP SWITCH Lab Manual, 2nd Edition | Pearson

Now, bring up the port by issuing the no shutdown command on the interface. Remember that the switch with the lowest MAC address becomes the root. If the sender port priorities are the same, the switch picks the port that receives BPDUs with the lowest sender port number. Change the revision number by typing revision number. Refer to the lab diagram for which ports to set up as trunks and the type of encapsulation to use.

The and switches have a range command that you can use to designate multiple individual ports or a continuous range of ports for an operation.

This machine is used by temporary staff employees. Page 7 of 7.

DHCP gives out dynamic IP addresses on a subnet to network devices or hosts rather than statically setting the addresses.

The switches can use different methods to load-balance traffic going through a port channel. How can you tell?