BTS GSM Installation Guide(V_13).pdf – Download as PDF File .pdf), and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. What is a base station installation guide 1) Introduction to base stations BTS Installation Guide for Enhancing Existing Cabinets ( Registering for a free account gives you a number of additional benefits, including access to additional valuable information that you can browse or download.

Author: Mikanris Grot
Country: Kuwait
Language: English (Spanish)
Genre: Love
Published (Last): 27 May 2012
Pages: 206
PDF File Size: 3.71 Mb
ePub File Size: 9.95 Mb
ISBN: 288-4-25464-960-2
Downloads: 34169
Price: Free* [*Free Regsitration Required]
Uploader: Shagore

Optional installing A Cpri Optical Fiber The performance of an optical module that is exposed to the air for more than 20 minutes may be abnormal.

Unpacking The Equipment The total number does not tally with the Find out the cause and report any missing packing list articles to the local Huawei office. Press the primary mouse button twice continuously mamual quickly without moving the pointer. The installation of cabinets must meet the requirements of the proper design, practical installation, and elegant layout. Reply 6 Thanks for your appreciation! Table of Contents Add to my manuals Add. Installation Guide for Enhancing Existing Cabinets.

Connected to the PGND cable.

Installation Environment Checklist Table describes the installation environment checklist. C Installation Guide 06 This is the sixth official release.

Huawei BTS3900L Installation Manual

The figure of the GPS surge protector is for reference only. Outdoor macro large base stations. If the current temperature maual out of the range, make protection measures or route the cables again.


Indoor centralized rack icr dual-mode base station pages. The armor of the AC cable need to be grounded.

Huawei BTSA Installation Guide V1 5 | Pradeep Liyanage –

If the resistance is greater than or equal to five megohms, you can infer that the cabinet is insulated from the jnstallation. C cabinet, as shown Figure Help Center Find new research papers in: Comments to this Manuals Your Name.

Therefore, the remaining cables besides the 12 ones must be routed through the other cable outlet.

Thanks a lot inshallation sharing. If DC power cables need to be routed on the tower platform, lay out the cables on the guardrail with the shortest distance and route the cables along the guardrail. Sufficient slack recommended for about 0. Step 1 Align manial holes on the cable holders with mounting holes on both sides of the BBU case, and then use two M4 screws on each side to secure the cable holes to 1. This installation guide plays great emphasis on impacts of new component installation on the running base station.

Welcome to Our Website

Compared with installatino 06no topic is added. Disconnect the equipotential cable from the lower part of the door. Types of base stations. Mark the positions of the mounting holes on manuall concrete floor, as shown in Figure To meet customer requirements, we supply various installaton guides, which are listed as follows: Page 73 Cable clips must be vertical with cables, and the cables in a cable clip must be parallel.


To print the manual completely, please, download it. Armetta Posted on Page 50 Step 8 Test the insulation between the base and the expansion bolt. Installation Guide 8 Installing the Cabinet Context When installing a BTSL on a base, use a marking template matching the base to determine the positions of the holes for installing the cabinet.

Command Conventions The command conventions that may be found mqnual this document are defined as follows. Use the multimeter to measure the DC output voltage, the normal range should be Page 44 Step 4 Test the insulation between the base and the expansion bolt.

Reset Password

Step 3 Remove the cabinet door to facilitate operations, as shown in Figure Installation Guide for Capacity Expansion. Before a cabinet is installed, you must familiar with the cabinet structure, application scenario, and space requirements. Page 53 Step 3 Lay out the cable by referring to Page Ensure that the heads of all the cable ties are outside the cabling teeth, as shown in Figure