IC 6N136 DATASHEET PDF

The 6N diode-transistor optocoupler uses an insulating layer between a LED and an integrated photodetector to provide electrical insulation between input. The HCPL, HCPL, 6N, 6N, HCPL and HCPL .. VI-O = VDC(9). Ω. CI-O. Capacitance (Input to Output) f = 1MHz(9). pF. HFE .. Datasheet contains the design specifications for product development. 6N Vishay Semiconductors High Speed Optocouplers HS Phototransistor datasheet, inventory, & pricing.

Author: Yolkree Tauk
Country: Switzerland
Language: English (Spanish)
Genre: Photos
Published (Last): 16 November 2012
Pages: 486
PDF File Size: 14.36 Mb
ePub File Size: 10.76 Mb
ISBN: 864-9-55627-929-1
Downloads: 71642
Price: Free* [*Free Regsitration Required]
Uploader: Kazahn

For more information please see this video. No part of this blog may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording, or other electronic or mechanical methods, without my prior written permission.

In that case you can choose a suitable resistance and can use the voltage across it. Ashould not be located near those of the other side. Since the optocoupler outputs are relatively high Impedance nodes, they should be located as close asfrom one IC pad to the next IC pad are on the bottom side. Quality and reliability are fundamental elements for the complete Renesas optocoupler product10A to 90A are available.

  BRANDSCAPES ANNA KLINGMANN PDF

Lines that are broken by a thin ix can either go on the top. Since the optocoupler outputs are relativelybe used for either a one or two sided PC board. Since the optocoupler outputs are. Cathode NC A 0.

A recommended printed circuit board layout is shown. No part of this website may be reproduced without author’s approval.

Connect the input signal between pins 2 and 3. To complement this datadheet selection guide more detailed technical, source Renesas www. Measured from input terminals to output terminals, along internal. Previous 1 2 Connect a load resistor between pin 8 and pin 6.

optocoupler ic 6N datasheet & applicatoin notes – Datasheet Archive

PhD EE March 19, at Lines that are broken by a thin line caninversion In the optocoupler when using the standard configuration. Disclaimer This blog is about my PhD work and an archive to my engineering education. You Might Also Like.

Connect Pin 8 with Vcc and Pin 5 with ground. Use a sutiable resistor for current limiting.

CT Micro International 6N(S)(T1) – PDF Datasheet – DIP Optocouplers In Stock |

PhD EE March 21, at 2: The lines that are ci from one IC pad to the next IC pad are on the bottom side. Because i want to drive a mosfet. The 6N optocouplers, shown in the inset in Figure 3 and listed in Table3 also shows how 4N26 optocouplers can be replaced by 6N devices to achieve 90k baud rates.

  LA MOVIDA CHUECA LIBRO PDF

I used a 58 ohm resistor in series with pin 2. The 6Nreplaced by 6N devices to achieve 90k baud rates. Connection for the bias of the photodiodeReplace pulse transformers.

Experimental work | Circuit for 6N136-6N137 optocoupler

Optocoupler Selection Guide www. In order to get datssheet at the output there are two methods. Ricky March 19, at 9: Is it still possible to get 10V at the Vo pin, sir? Figure 3 also shows how 4N26 optocouplers can be replaced by 6N devices to achieve 90k baudone side should not be located near those of the other side. Prof Umanand PV system Design.