KEMA 08 ATEX IECEx KEM Features. □ Wide temperature range . □ PLEXO connection system, cold-applied connection and shrinkable tubing. EU-Type Examination Certificate Number: KEMA 98ATEX X are recorded in confidential test report number NL/KEM/ExTR/ KEMA 05ATEX X. PTB 02 ATEX X. Electrical KEMA 08ATEX SEV 10 ATEX SEV 10 ATEX SEV 10 ATEX SEV 10 ATEX.
|Published (Last):||17 October 2015|
|PDF File Size:||7.85 Mb|
|ePub File Size:||14.73 Mb|
|Price:||Free* [*Free Regsitration Required]|
The temperature deviation is 1 K at most. AC V min.
Technical data | Heating Technology
There is an optical and acoustic alarm signal. The energy controller is energised via V mains supply voltage. Rated voltage V up to Temp. By pressing a single button, the controllers power output is displayed, allowing an evaluate of the heating circuits quality.
TYPE APPROVAL CERTIFICATE
Over insulation caution labels The enclosure is mounted by means of insulated screws outside of the lid seal. The set point value is determined by the MC32 controller. The internal, galvanically isolated bus connection is established by simply joining the modules ate by means of RJ plug connectors.
This simplifies planning and installation. That splices and connections can be dismantled easily, is easy to service. Once done, a status LED flashes.
A temperature limiter is not necessary also not in hazardous areas. See System Description for the Installation Instructions. Afterwards ferrules are placed. It is the choice of the correct system which guarantees the satisfaction of all your individual requirements. For the different temperature areas you can choose between several versions in three-wire-connection. If there is a break in the measuring system leakagethe circuit remains open permanently.
There are two versions of the EMK connection kit available: 088 addition to the control parameters, customized high- and low-temperature alarms can be set by the operators. Nominal voltage Code no.
TYPE APPROVAL CERTIFICATE – PDF
PSB 33 35 While the polyolefin protective jacket is used where there are aqueous, inorganic chemicals, the fluoropolymer outer jacket is suitable for organic chemicals. For each measuring channel up to m of sensor cable can be connected.
Non-Bartec enclosures may be used in some cases, however suitability for marine environments and correct Ex-rating if in hazardous area should be considered before installation. Cable thermostat KTE-m, B Typical applications are switchgear and controlgear cabinets, instrument housings, analyser cases, arex boxes and other enclosures. If the sensor temperature exceeds the pre-set level, the contact is actuated. The heating tape is cut and terminated directly on the construction site according to the circumstances.
Heating of analyzer systems Precision heating of pulse and measurement performances ated tapping to analyser system. Silicone heater plate for control cabinets SSM, Installation kit explosion protected set fold set Order no. This membrane is connected to a mechanical device that activates mema microswitch.
Displays LEDs in the front of the enclosure: These regulate the outputted heating power as well as the holding temperature. Heaters, fans, motors and other equipment are energised and de-energised when temperatures fall below or rise above certain limits. The use of high-quality, corrosion-proof material guarantees the application of the systems even under atxe conditions as, for example, prevail kdma the chemical industry, petrochemical industry and waste incineration plants.
The outer cover is made of thermoplastic elastomer TPC default for areas with special requirements to chemical resistance and mechanical strength. To make this website work, we log user data and share it with processors. For special applications which require chemical resistance and mechanical strength a fluoropolymer insulation-jacket is optionally available.
Higher switching currents or 3-phase applications are switched by means of a contactor. For not every system is suitable for every application. Circuit diagram Accuracy of reference junction with thermocouple measurements 0.
kema 08 atex pdf – P(1) –
One cable gland with size M25 for the power cable is already assembled at the junction box. The system is easy to plan and configure. The end of the self-limiting heating tape is insulated with silicone glue and a silicone end cap. High quality stainless steel System Aluminium junction boxes are available on request.
A sophisticated sealing system offers safe and reliable protection against adverse weather conditions.
IP 53 Type As it meets the requirements of the Ex m type of protection, intrinsically safe circuits can be dispensed with. The limiter function can be suppressed by a digital input when carrying out servicing work on the heating circuit, e. Once the temperature drops, the temperature limiter can be unlocked manually.
Inner polyolefin electrical insulation jacket thermally fused to the heating element bonded jacket 4. Cable gland IP 67 for power supply cables Supply voltage max.