View and Download AMMCO installation instructions manual online. Disc Rotor Lathe. Lathe pdf manual download. iv • AMMCO Brake Lathes. Safety. Safety Notices and. Decals. For your safety, and the safety of others, read and understand all of the safety notices and . Get AMMCO Disc Rotor Lathe Manual. Get all AMMCO manuals!.
|Published (Last):||12 October 2005|
|PDF File Size:||3.4 Mb|
|ePub File Size:||9.64 Mb|
|Price:||Free* [*Free Regsitration Required]|
Turn the left hand tool bit control until the tool bit contacts the rotor surface and makes a scratch cut no deeper than. Care Of Arbors And Adapters Handle the adapters and arbors with care and store them on individual hooks. Make sure that the tool bits clear the rotor faces and the silencer band.
Do this for your own protection. This is caused by runout or wobble due to rotor condition or by the way the rotor is mounted on the arbor.
AMMCO Disc Rotor Lathe User Manual | 20 pages
KEEP these and other materials delivered with the unit in a binder near the machine for ease of reference by supervisors and operators. Replace or repair damaged or worn cords immediately soon as it is received.
The patented self-aligning spacer prevents diagonal thrust on the adapters. Table of Contents Add to my manuals Add.
Proper maintenance and inspection is necessary for safe operation. Or point us to the URL where the manual is located. When the cross feed has amnco the cutting tools all the way across the face of the rotor, the feed will shut off automatically.
Unplug unit from power source before servicing or adjusting. Tell us what’s missing.
Also inspect the rotor hub for loose or damaged bearing cups. Brake Lathes The scratch will usually appear as an incomplete ammco. Either rough or finish cuts may be taken to resurface a rotor.
After the brake rotor is mounted on the arbor, install the silencer band. By pressing ‘print’ button you will print only current page.
Identify the hazard levels used in this manual with the following definitions and signal words: A true running arbor is essential to professional quality rotor reconditioning. DO NOT throw them into a ammck.
AMMCO 7000 Disc Rotor Lathe User Manual
Use a micrometer to check the thickness of the rotor at no less than three points around the circumference about 1″ The witness marks should be carefully aligned when installing the arbor, Fig. Table Of Contents Cleaning To drain the oil, remove the socket head drain plug located on the front of the lathe to the right of the cross feed assembly, Fig. qmmco
Brake Lathes Installation Receiving The shipment should be thoroughly inspected as soon as it is received. Now engage the automatic cross feed by moving the knobFig.
Recheck the setting of the depth-of-cut collars which were on zero. Reset the collars if necessary. Brake Lathes Arbor Installation The 1″ arbor shipped with the lathe has been carefully matched to the lathe during final assembly and testing. Page 15 Examine each adapter and the arbor for nicks, burrs, chips, dirt, and rust.
AMMCO Disc Rotor Lathe : Manual
Don’t have an account? The cross also be operated manually using the cross feed handwheel. Safety Notices And Decals For additional copies of either, or further information, contact: Chips and dust ammdo be driven between machined parts and into bearings causing undue wear. Also always wear safety glasses or a face shield. Turn the cross feed handwheel back about a half turn, start the lathe and move the tool bit in to make a second scratch cut.
B 10, and adjust the twin cutter so that the rotor is centered between the tool bits. Keep bystanders out of aammco area. Handle the adapters and arbors with care and store them on individual hooks.
Page of 20 Go. Read entire manual before installing, operating, or servicing this equipment. Examine each adapter and the arbor for nicks, burrs, chips, dirt, and rust.
What’s missing? Tell us about it.
Even the smallest nick, scratch, or loose chip can cause incorrect rotor alignment, resulting in inaccurate machining. Center the twin cutter to the rotor. Page 19 Brake Lathes Care of Ammck and Adapters CAUTION Although the adapters, arbors, and the spindle are made of top grade steel and are turned, hardened, and precision ground to close tolerances, great care should be taken in their use, handling, and storage. Every hours drain the oil and refill to the dipstick level with clean EP gear oil.
Comments to this Manuals Your Name. Witness marks have been etched onto the arbor and spindle for repeatable, precise alignment. Give the rotor a full turn by hand and start the lathe.